Материал из WikiGamia
It really is simple to make your own archery kit, when you have the appropriate gear. For this you need: a 5-foot branch and a 1 or 2 foot branch for the arrow hemp string feathers flint stone or metal dead sticks of about 12 to 18 inches feathers cardboard and a knife.
For the bow, pick a piece of dead wood, preferably bendable and at least an inch in diameter and 5 foot long. Cut two notches in the branch, about 1 1/two inches from each finish. The notches should go about halfway into the bow and should be on the side of the bow opposite from the branch's natural curve.
The smaller branches are for the arrows. Make these as straight as feasible, sanding them if required. Cut 1 notch at the end of the arrow, producing a good hook. This is exactly where the string will sit at the finish of the arrow, so make a nice deep groove.
Next cut a piece of your hemp string about 3 fourths of the length of the bow. It need to be smaller than the bow. Tie loops at each and every end of the string that are large enough to fit about the notch that you made in the final step. Take the loops that you just tied and place them around the notches on every end of the stick.
Now take the cardboard papers and cut them into elongated triangles. The legs (bottom) should be roughly 1.25 inches by 1-three/4 inches. Once you have about 6 of them cut out (for 2 arrows) glue them about .25 inches from the bottom of the arrow. Hold in mind you must hold them evenly spaced from every single other. They really should give for balance, accuracy, and a good spin when the arrow is released. It is straightforward to make your own archery kit, when you have the appropriate gear. For this you need to have: a five-foot branch and a 1 or two foot branch for the arrow hemp string feathers flint stone or metal dead sticks of about 12 to 18 inches feathers cardboard and a knife.
For the bow, decide on a piece of dead wood, preferably bendable and at least an inch in diameter and five foot long. Cut two notches in the branch, about 1 1/two inches from every finish. The notches ought to go about halfway into the bow and should be on the side of the bow opposite from the branch's all-natural curve.
The smaller branches are for the arrows. Make these as straight as possible, sanding them if required. Cut 1 notch at the finish of the arrow, generating a good hook. This is exactly where the string will sit at the end of the arrow, so make a good deep groove.
Next cut a piece of your hemp string about 3 fourths of the length of the bow. It need to be smaller than the bow. Tie loops at every single end of the string that are large sufficient to fit around the notch that you produced in the last step. Take the loops that you just tied and put them around the notches on every single end of the stick.
Now take the cardboard papers and cut them into elongated triangles. The legs (bottom) must be around 1.25 inches by 1-three/4 inches. The moment you have about 6 of them cut out (for two arrows) glue them about .25 inches from the bottom of the arrow. Maintain in thoughts you should preserve them evenly spaced from each other. They really should supply for balance, accuracy, and a nice spin when the arrow is released. It really is effortless to make your personal archery kit, the moment you have the proper equipment. For this you need to have: a five-foot branch and a 1 or two foot branch for the arrow hemp string feathers flint stone or metal dead sticks of about 12 to 18 inches feathers cardboard and a knife.
For the bow, choose a piece of dead wood, preferably bendable and at least an inch in diameter and 5 foot extended. Cut two notches in the branch, about 1 1/2 inches from every end. The notches should go about halfway into the bow and must be on the side of the bow opposite from the branch's natural curve.
The smaller branches are for the arrows. Make these as straight as possible, sanding them if needed. Cut a single notch at the finish of the arrow, generating a nice hook. This is exactly where the string will sit at the finish of the arrow, so make a nice deep groove.
Next cut a piece of your hemp string about 3 fourths of the length of the bow. It must be smaller than the bow. Tie loops at every single finish of the string that are huge enough to fit around the notch that you created in the final step. Take the loops that you just tied and put them about the notches on every single finish of the stick.
Now take the cardboard papers and cut them into elongated triangles. The legs (bottom) really should be around 1.25 inches by 1-three/four inches. As soon as you have about 6 of them cut out (for two arrows) glue them about .25 inches from the bottom of the arrow. Keep in thoughts you should maintain them evenly spaced from every single other. They must supply for balance, accuracy, and a good spin when the arrow is released. It's easy to make your personal archery kit, once you have the appropriate gear. For this you require: a five-foot branch and a 1 or two foot branch for the arrow hemp string feathers flint stone or metal dead sticks of about 12 to 18 inches feathers cardboard and a knife.
For the bow, select a piece of dead wood, preferably bendable and at least an inch in diameter and five foot extended. Cut two notches in the branch, about 1 1/2 inches from each end. The notches must go about halfway into the bow and have to be on the side of the bow opposite from the branch's natural curve.
The smaller branches are for the arrows. Make these as straight as feasible, sanding them if required. Cut a single notch at the finish of the arrow, generating a nice hook. This is exactly where the string will sit at the end of the arrow, so make a nice deep groove.
Subsequent cut a piece of your hemp string about 3 fourths of the length of the bow. It have to be smaller than the bow. Tie loops at every single finish of the string that are big sufficient to fit around the notch that you created in the final step. Take the loops that you just tied and put them around the notches on every single end of the stick.
Now take the cardboard papers and cut them into elongated triangles. The legs (bottom) should be approximately 1.25 inches by 1-three/four inches. As soon as you have about 6 of them cut out (for 2 arrows) glue them about .25 inches from the bottom of the arrow. Hold in mind you must preserve them evenly spaced from every other. They should provide for balance, accuracy, and a nice spin when the arrow is released.
|
Лучшие игры
Игры по категориям
|
Рейтинг пользователей
Во что сейчас играют
Последние комментарии
|
52399 
2 
61
